Psa LIFPE9/1 Manuel d'utilisateur télécharger pdf

PHOTOELECTRIC 9 VOLT

BATTERY OPERATED

SMOKE ALARM MANUAL

MODELS:

LIFPE9/1

LIFPE9M

MAIN FEATURES:

• PHOTOELECTRIC SENSOR SUITABLE

FOR SLOW SMOULDERING FIRES

• INSECT SCREEN SURROUND PE

SENSOR

• SLIM-LINE COMPACT SIZE

• MUTE & ALARM TEST BUTTON

(LIFPE9M)

• ALARM TEST BUTTON (LIFPE9/1)

• LOW BATTERY WARNING SIGNAL

• MOUNTING SCREWS SUPPLIED

• COMPLIES & APPROVED TO

AUSTRALIAN STANDARD AS3786

• LOUD 85dB ALARM

This instruction leaflet contains important

information on the correct installation and

operation of your smoke alarm. Please read

all the information before commencing

installation and retain for future reference.

SPECIFICATION

Power Source : 9V Battery

Battery Type : Eveready 1222

: Energizer 522

Gold Peak 1604S

Duracell MN 1604

Ultralife U9VL

Operating Temp. : 0°C to 45°C

Ambient Humidity : 10%-90%

Alarm Sound Level : 85 Decibels at 3 metres

Battery Life : 1 year minimum

Tested & Passed to : AS3786-1993

LOCATING THE SMOKE ALARM

This smoke alarm is a single station photoelectric

alarm and should NOT be connected to other

smoke alarms. If your dwelling is a single storey,

for minimum protection you should fit a smoke

alarm in the hallway between the living areas

(incl. kitchens) and sleeping areas. Place it as

near to the living areas as possible and ensure

the smoke alarm is audible and can be heard

when the bedrooms are occupied. See Figure 1

for examples.

If your dwelling is multi storey, for minimum

protection a smoke alarm should be fitted at the

bottom of the staircase with further smoke alarms

fitted on each upstairs landing. This also includes

basements. See Figure 2 for examples.

NOTE: For maximum protection a smoke alarm

should be fitted in every room (except kitchen,

bathroom and garage). DO NOT FIT A SMOKE

ALARM IN THE KITCHEN or BATHROOM, as

cooking fumes or steam may trigger the smoke

alarm. A Photoelectric smoke alarm may be

located near the kitchen but not directly over the

cooking area.

DO NOT FIT A SMOKE ALARM IN A GARAGE,

as exhaust fumes are likely to set it off.

POSITION THE SMOKE ALARM

As smoke rises, it is advisable to mount the

smoke alarm on a ceiling in a central position.

Avoid areas where there is no air circulation.

Such as corners of rooms, in the peak of an

“Ä” frame type of ceiling and air ducts used for

heating and air conditioning. If wall mounting,

do not mount tight into corners. See Figure 3 for

example. Areas to be avoided include the

following:-

• Situations where the temperature may fall

below 0°C or rise above 45°C.

• Humid areas such as bathrooms, kitchens and

shower rooms where the relative humidity may

exceed 90%.

• Fume filled environments such as garages.

Exhaust gases may also cause false alarms.

• Adjacent to or directly above hot components

such as radiators or wall vents that can affect

the direction of air currents

• In very dusty or dirty environments such as

workshops

FIGURE 1 – SINGLE STOREY DWELLING

FIGURE 2 – MULTI STOREY DWELLING

 Smoke alarm for minimum protection

 Smoke alarm for additional protection

FIGURE 3 – POSITION THE SMOKE ALARM

INSTALLING THE SMOKE ALARM

This smoke alarm is powered by a battery

and requires no additional wiring.

• A mounting plate is provided on the back

of the smoke alarm.

• Remove the mounting plate from the back

of the smoke alarm by holding the mounting

plate and twisting the smoke alarm in the

direction indicated by the “OFF” arrow on

the smoke alarm cover.

• Having established the mounting location,

ensure that there is no electrical wiring or

pipe work in the area adjacent to the

mounting surface.

• Take the mounting bracket and mark two

mounting hole locations.

• Drill holes in the positions marked.

• Insert the wall plugs into the drilled holes.

• Screw the mounting plate to the mounting

surface. DO NOT OVER TIGHTEN.

• Attach the battery to the connector clip

and then place the battery as shown in

the illustration in the compartment.

• Place the smoke alarm on the mounting

plate and rotate the alarm until it connects

into the mounting plate. Twist the smoke

alarm in a clockwise direction until you

hear 2 clicks. The smoke alarm is now

locked in position.

• Test the smoke alarm for correct

operation using the test button facility.

1 2

Résumé du contenu

Page 1

PHOTOELECTRIC 9 VOLT BATTERY OPERATED SMOKE ALARM MANUAL MODELS: LIFPE9/1 LIFPE9M MAIN FEATURES: • PHOTOELECTRIC SENSOR SUITABLE FO

Page 2

TAMPER PROTECTION FEATURE To make the smoke alarm tamper protected, a tamper resistant means has been provided. To utilise this feature brea

Modèles reliés LIFPE9M

Commentaires sur ces manuels

Pas de commentaire

Psa LIFPE9/1 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Sécurité Psa LIFPE9/1. PSA LIFPE9/1 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés LIFPE9M

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Psa LIFPE9/1